Showing posts with label cisco. Show all posts
Showing posts with label cisco. Show all posts

Saturday, August 25, 2012

Basic Cisco QoS for IP Phone System to IP Phone VoIP System Voice Garbled

Share/Save/Bookmark

Sample Cisco QoS for IP Phone System to IP Phone System to Solve Distorted Voice Quality

In this situation, the remote office's router is a Cisco 1841. The VoIP (voice) over a  legacy T1 Point-to-Point was garbled. The conversations sounded like the callers were underwater. There was need to clear up the voice quality and the best method to do so was to use QoS.  The unclear voice occurred on nearly all phone conversations both internal and external. The phone sets at the remote office were digital but the phone system is IP (VoIP) based. The remote office phone system and the phone system at the main office communicated via IP.  The simple solution, using the existing hardware already installed, for this problem was to implement QoS on the router. The goal was to prioritize the voice packets that were sent in and out of the router from one system to another. At the same time, the goal was to also keep the solution as simple as possible.

Cisco Remote Office Router - QoS class-map, policy-map, and access-list on router for Voice Quality

This simple basic QoS example firstly required a simple access list that contained both of the phone systems' ip addresses. After the simple access-list, a class-map and policy-map were also configured on the router. In the end, the policy map is applied to an interface.
 First, in configuration mode of the router,  the access-list. is created.  The access list basically will contain a lists of our phone system ip addresses for the main office and the remote.

Replace the ip addresses shown below with the ip addresses of your phone system. Also, if the access-list number is already taken on your router for another access-list, use another number. This example uses 101 for an extended access list.

   access-list 101 permit ip any host 192.168.1.10
   access-list 101 permit ip any host 192.168.2.10

 Next, create a class-map on the branch router. The class-map is basically a map or list of the match criteria. If you haven't guessed it already, the match criteria will be the ip addresses of the phone systems. In the class-map, we add "match access-group 101. 101 is the access list that contains our phone systems' ip addresses.
    class-map match-any IPPhoneSys-to-IPPhoneSys
   match access-group 101

 After the access-list and class-map is configured, the class-map is applied to the policy map. The policy map can contain more than one class-map.  So the policy-map is like a list of class-maps. The policy-map is applied to an interface. In this example it will be the serial interface corresponding to the T1 (point-to-point T1).: The bandwidth statement is key to what we are trying to accomplish. This is a simple example of QoS so I have just merely taken 20 percent of the bandwidth and pretty much assigned it to voice (VoIP)

    policy-map QoS_Policy_Priority
    class IPPhoneSys-to-IPPhoneSys
    bandwidth percent 20
    class class-default fair-queue

In this example it is a legacy point-to-point T1 that connects the two offices. The interface you use may differ. To apply the policy-map that contains the class-map with 20 percent bandwidth defined for voice change to the interface level commands by entering the interface on which you plan to apply the QoS policy map. In this example it is a serial interface for the t1 (S0/0/0)

    config# interface serial0/0/0

 Then apply the policy on the interface by running the command

    service-policy output QoS_Policy_Priority

 The above is a simple basic QoS policy using one of the many Cisco Modular QoS solutions. Once applied, it cleared the voice issues immediately. In the example above the bandwidth reserved for voice over ip (VoIP) was 20 percent. You can change that percentage to fit your environment.

QoS can be applied to all types of data streams including RDP (remote desktop protocol).  Applicable for access to server and desktop or for managing RDP.  The protocol by port number or IP address can be managed so that it's given higher priority, or lower priority if that's what the situation requires. RDP port setting can be set to a custom value on RDS servers for standard access or for managing RDP (Terminal Server). 
 

Tuesday, April 04, 2006

Cisco 2811XM Installed fine


A local bank has asked my company to swap out some aging routers for new Cisco 2811XM series routers for the branches and a couple of 3825 series for the core. the first of the branch routers went in today with out a hich. I prepped the router in the office with updates to the IOS and setup the router's start-up and running configuration to match the old router this was replacing. The difference being this unit had different port enumerations. I did call in for some tech support on a DR site branch. I must say Cisco's TAC is not as good as it used to be. below is an image of the 2811XM router. They are bit larger that the 2600 series.

Tech support software to allow remote computer control through the web:


Software for PC Remote Support

Applications such as software for PC remote support allows for access to remote computer users computers through the web for support. Once connected, the technician can work on desktop applications, operating system problems, mis-configurations, or network router (internet routers too). Although most remote support applications won't permit direct remote control access to routers on an internal network, they do get access onto a computer desktop or server that is on the remote local network. From that point, the router can be accessed. Alternatively, SSH (or even less secure Telnet) can be enabled on the router and access from the Internet could be enabled on the edge router/gateway. 4RemoteSupport software for PC remote support provides such a method for access via the Internet. Web based software for PC remote support enables technical support remote access to an internal computer. Once on the remote computer on the remote network, the computer can be used a jump point to the router.  Although web based software options for SSH online applications aren't common, there are installable or desktop based applications for SSH connections to routers. Most SSH implementation are installed 32bit or 64 bit applications such as Secure CRT. Others that are lighter and can run without installing are for example Putty. It is a portable executable application that can just simply be run from a command prompt or by double-clicking the main executable file for supporting devices remotely.

More Info:

Software for PC Remote Support

Previous post entries with similar topic:http://remotesupportpc.blogspot.com/2006/10/remotely-support-desktops-over.html

http://remotesupportpc.blogspot.com/2006/06/remote-support-software.html

Blog:

Evolution of Technology and Support - Desktop Tech Support


Thursday, January 26, 2006

PIX VPNs going down. Computers can't connect.




Main office has a Cisco PIX 506. Three remote offices have pix 501s. Yesterday one of the small remote office pix wouldn't establish VPN tunnel so remote computers at the location wouldn't connect back to the office. Today another small office's vpn tunnel wouldn't establish even on reboot. Used some remote support software that provided me on-demand pc remote control of one of the remote desktop systems at the remote office then telnetted to the PIX and ran the VPN client connect command from the enable prompt. This command re-established the VPN and the computers got through to the main office LAN. Who knows what the problem is. If I find the problem I will surely post it as it might help someone else.


Share/Save/Bookmark

Thursday, January 05, 2006

Remote Support Software - Cisco

Cisco Webex

There are a lot of software companies out there (on the internet that is ) that have on-demand remote pc control PC software for online remote desktop support available. I mean there are tons. features and functions vary among some of the tools but at the core the goal is to get remote access of a computer wither over the web online or inside your own network such as a LAN which includes WiFi networks. 

High-end to Free

There's everything from the hi-end Cisco Webex to free stuff that takes a little more work and know how to get going but are usable. There are also the tried and true types like pc-anywhere for remote PC support on-demand that were all familiar with. At least those of us that are in the computer business in one way or another. The VNC flavors that are mostly free and have been around for ages. VNC though has been a good useful tool for many years and for thousands of companies and it still does the job. Plus it has a very small footprint and is very versatile. The remote support software industry is just booming. Remote controlling computers over the internet seems to be the thing. A very useful thing. Especially when the tech person doesn't have too much to get the remote system under there control. I'll have more on the next post . . .the baby is crying and I have to give the wife a hand and take this "call" .